8pin EPS x4 (As many inputs must be used as outputs). Pump: (Not included): Compatible with all D5 pumps.Ĭore Component Cables: 24pin x1. Reservoir, Pump Top, Pump Cover, Fill Port, Drain Port, Parts of water-cooling loop. The two on top of the PSU shroud cannot be used with vertically mounted GPUs. Two are on the top of the PSU shroud, four inside of the PSU shroud and there is one integrated on the PowerBoard. Spectre 3.0 Integra has 7x 2.5” Drive positions. The radiator mounting panels have a large range of adjustment to help with port alignment to the distribution plate. The PowerBoard can handle the most high-end PSUs and components. For the water-cooling system it can fit 2x 360mm radiators 60mm thick with a single set of fans or 2x 360mm radiators 40mm thick with two sets of fans, and the D5 pump. It is designed for fit the largest high-end GPUs. Spectre 3.0 Integra fits XL-ATX motherboards and has 8 expansion slots. The fill port is at the highest point on the back for the case and the drain point at the lowest point. The reservoir was designed to remove air as quickly as possible making the loop easier to fill. The pump top was designed for the D5 pump, maximizing flow to and from the distribution plate. ![]() The integrated loop routes in Spectre allow for more flow than 16mm tubes. This meant that we could focus more on optimization than would normally be possible. With the integration we did not just develop a case, we also developed all the integrated components. For Spectre Integras integration each port and connector were positioned based on an average of a vast range of components. Theoretically the more integration the less compatibility. The pump top, reservoir, cables, hubs, less fittings, less tube, no cable combs, or cable management components. These are components you do not have to purchase for your build. No cable management for the core component cables thanks to the PowerBoard integration.Ī large portion of the case cost is due to the integration. With the pump, reservoir, fill and drain ports, half of the water-cooling loop, the core component cables, PWM and ARGB hubs all integrated there is less assembly to be done. Spectre 3.0 Integra comes included with a standard set of black sleeved linking cables including 24pin x1, 8pin EPS x2, 8pin PCIE x3 meaning that these cables don’t have to be purchased separately. It is a new method for cables allowing standardization of cable lengths and making cable management no longer necessary. Essentially the PowerBoard is a distribution plate for cables also integrating other features and functions. The PowerBoard has x20 ARGB LEDs positioned around the external and internal perimeter to optimally light up the distribution plate. The Spectre 3.0 Integra PowerBoard also has an integrated touch sensing Power Button. The PowerBoard is a PCB integrating 24pin, PCIE and EPS along with PWM and ARGB Hubs, SATA and Power and Reset Buttons. Reservoir, D5 Pump Top, D5 Pump Cover, Fill Port, Drain Port, parts of the cooling loop. There are two separate sets of LEDs for ARGB or UV, and they can be switched on or off, or from UV to ARGB via two switches on the PowerBoard. Integra has improved lighting features with integrated PowerBoard LEDs facing inwards towards the motherboard tray and outwards towards the distribution plate. Custom colored sleeved linking cables can be purchased separately if desired. Black sleeved linking cables are included with the case, so no cables need to be purchased separately. There is now no rear access needed to the distribution plate layer due to the fully integrated PowerBoard, so all cables can be connected from the front and little to no cable management is needed. The PowerBoard has a range of new features, including built in filter capacitors, more integrated LEDs facing inwards and outwards, integrated direct connect SATA, power, and reset buttons, and a touch activated power button. The case has more support for larger and wider motherboards than previous Spectre 3.0 versions. The PowerBoard supports the most high-end components with x4 8pin EPS and 圆 8pin PCIE. This means that both have become far more streamlined, meaning more features and compatibility. Previously we have created PowerBoards for existing cases, but for Integra we have developed the PowerBoard and case together. It has a fully integrated solution/replacement for cables with the Singularity Computers PowerBoard. ![]() Spectre 3.0 Integra has much of the water-cooling loop integrated with a completely new distribution plate design, with further enhancements to performance, filling and draining compared to previous Spectre versions. The next generation of Spectre has arrived with a new level of integration.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |